| 62 | 0 | 91 |
| 下载次数 | 被引频次 | 阅读次数 |
本文聚焦锂离子电芯极柱区域超温对性能劣化的影响,通过实验揭示热-电-力多物理场耦合效应下的电芯失效机制。试验通过在极柱外侧的busbar(连接片)上覆盖加热片进行局部加热,热量沿“busbar—极柱—极耳”路径传入电芯内部,复现极柱超温状态,并以极柱温度作为控制与监测对象。研究发现,极柱超温引发了电芯内阻及膨胀力异常增长,导致循环寿命大幅缩短。拆解电极的微观结构与循环IC测试表明,高温会加速电解液分解与电极材料失效。正极颗粒破碎、负极层状结构破坏及锂沉积等现象会加剧电化学活性损失。不同温度下电芯劣化机制差异显著:60℃以SEI膜增厚为主,70℃则呈现多因素协同失效。研究强调了极柱超温是性能劣化的关键诱因,电极材料热稳定性与busbar设计优化对抑制失效具有重要意义。本研究为高功率电池系统中busbar热安全设计与寿命预测提供了实测依据与理论支持。
Abstract:This study focuses on the impact of pole overheat on the performance degradation of lithium-ion cells, revealing the failure mechanisms of multi-physics coupling effects (thermal, electrical, and mechanical fields). The terminal overheat state is reproduced by locally heating the busbar mounted outside the cell terminal, with heat conducted into the cell along the "busbar–terminal–tab" path, and the terminal temperature is taken as the control and monitoring target. The results show that pole overheat significantly induces a sharp increase in cell internal resistance and abnormal expansion force, leading to a substantial reduction in cycle life. Microstructural analysis of decomposed electrodes and incremental capacity (IC) tests demonstrate that high temperatures accelerate electrolyte decomposition and electrode material failure. Phenomena such as cathode particle fracture, anode layer structure damage, and lithium deposition exacerbate electrochemical activity loss. The degradation mechanisms differ significantly under different temperatures: SEI film thickening dominates at 60 ℃, while multi-factorial synergistic failure occurs at 70°C. The study emphasizes that pole overheat is a critical factor in performance degradation, and the thermal stability of electrode materials and optimization of busbar design are crucial for suppressing failures. This research provides experimental evidence and theoretical support for thermal safety design and life prediction of poles in high-power battery systems.
[1] 王仁杰.机电交互作用下锂离子电池失效演化机制及模型研究[D].哈尔滨:哈尔滨工业大学,2025.
[2] 罗海灵.机械滥用下的锂离子软包电池结构失效机理与建模研究[D].北京:清华大学,2018.
[3] 杨凯,杨晓光,王文伟,等.锂离子电池电化学-热-力多物理场耦合建模综述[J].电源技术,2025,49(5):887-897.
[4] 卜毅,唐付靖,戴翼昊,等.锂离子电池电化学-机械耦合行为的膨胀测评体系研究[J].汽车科技,2026(1):60-65.
[5] 周远翔,魏振强,袁新齐,等.锂离子电池枝晶内短路引起的电热效应研究[J].电气工程学报,2025,20(5):273-282.
[6] 徐涵.钠离子电池衰退行为与性能优化研究[D].广州:广东工业大学,2025.
[7] 罗磊鑫,杨力帆,张兴伟,等.磷酸铁锂电芯过充产物实验研究及热失控判断方法[J].电工技术,2023(23):45-49.
[8] 黄建华,阮毅,林敏.电池铝巴的扩散焊接及其剥离力检验[J].机电工程技术,2021,50(7):53-55.
[9] CHOI J G,PASCASIO J D,LEE J.High C-rate Li-NMC/graphite pouch cell end-of-life predictionviacycle-dependent variations and machine learning[J].Dalton Transactions,2025,54(24):9754-9760.
[10] 王方,吴泽昊,苗秀娟,等.老化锂离子电池机械滥用安全性研究综述[J].中国科学:技术科学,2025,55(7):1077-1104.
[11] CHI A,GAO Y,JIANG Q S,et al.Overheat-to-thermal-runaway characteristics and fuzzy risk assessment of automotive lithium-ion cells with different cathode materials,capacities,packaging,and states of charge[J].Journal of Power Sources,2025,659:238470.
[12] CHUNG H,KANG B.Mechanical and thermal failure induced by contact between a Li_(1.5)Al_(0.5)Ge_(1.5)(PO_(4))_(3) solid electrolyte and Li metal in an all solid-state Li cell[J].Chemistry of Materials,2017,29(20):8611-8619.
[13] KIRCHEV A,GUILLET N,LONARDONI L,et al.Li-ion cell safety monitoring using mechanical parameters:Part II.Battery behavior during thermal abuse tests[J].Journal of the Electrochemical Society,2023,170(1):010503.
[14] BAECK K H,SONG Y B,KIM D,et al.Chemo-mechanical failure and reinforcement of solid electrolyte films for practical all-solid-state Li metal pouch cells[J].Advanced Materials,2026,38(16):e18655.
[15] ZHANG X,LIU W L,YUAN S,et al.Finite element analysis of soldering-induced thermomechanical stress and deformation in multi-busbar interconnected solar cells[J].Solar Energy,2025,299:113713.
[16] WANG C Y,LI C L,WANG G F,et al.Fast identification method for thermal model parameters of Lithium-ion battery based on discharge temperature rise[J].Journal of Energy Storage,2021,44:103362.
[17] APHALE S,LULLA S,MARATHE S.Influence of state of charge on deformation induced mechanical failure in Li-ion cells[C]//2020 IEEE International Conference on Power and Energy (PECon).December 7-8,2020.Penang,Malaysia.IEEE,2020:282-287.
[18] KUMAR N,PAMARTHI V V,MOFFAT J,et al.In-depth evaluation of laser welding of thick busbar to 21700 Li-ion cell terminal for electric supercar vehicle battery pack[J].Journal of Materials Research and Technology,2024,33:3058-3067.
[19] LEE J,LEE S.Impact of busbar-induced joule heating on battery temperature rise in electric vehicle batteries[J].International Journal of Automotive Technology,2026,27(1):285-294.
[20] LI J X,LI P Z,WANG M,et al.Study on the temperature rise characteristics of aging lithium-ion batteries under different cooling methods[J].Applied Thermal Engineering,2024,240:122235.
[21] HAO Y Q,YI D B,ZHANG X W,et al.A power management IC used for monitoring and protection of Li-ion battery packs[J].Journal of Sensors,2021,2021:6611648.
[22] ZHU G Q,HUANG X M,YOU Y,et al.Multi-cell battery sensing and protection IC with integrated low-temperature-drift reference for series battery pack management[J].IEEE Transactions on Circuits and Systems I:Regular Papers,2025,72(10):5634-5645.
基本信息:
中图分类号:TM912
引用信息:
[1]邓杰,梁锐,高毓轩,等.极柱超温对锂离子电芯性能劣化的影响分析[J].电池工业().
2026-10-10
2026-10-10
2026-10-10